Author Archive for Dave Tursi

Another delighted client in Rock Hill South Carolina

Rock Hill inspection week of 8/3/2020. Short summary on this inspection. Images highlighted show downspouts needing extension from foundation wall, and condensate drain line discharging at foundation wall. Both corresponding pictures are paired with crawlspace images where visible moisture is wicking through masonry wall via efflorescence. Wood rot present at base of columns and railings front and back porch. Loose toilets on the inside. Nice home, small summary, happy client.

York South Carolina inspection

Inspection in York South Carolina week of 8/3/2020. Numerous defects present in this home including but not limited to: 100% moisture reading in master bedroom exterior wall. Further outside evaluation revealed water leaking back into structure underneath this area while raining, another source for moisture could not be ruled out as well. Last three images. Numerous electrical issues, Scorched frayed wires openings in panel neutral bus not grounded to box, Wires not properly labeled, a Zinsco exterior panel box was present. Multiple areas of wood rot present on exterior cladding, Rear deck in disrepair, and the cost of repairing it may outweigh the cost of just replacing it, plus numerous other smaller issues all going on summary and the larger ones being cited for further evaluation by a licensed contractor.

Foundational movement, fire damage

I was hired by my client, on this particular inspection, to give an opinion on just the major systems of the property in question, a turn of the century foursquare home. HVAC systems were old and inoperative, No water heater present, electrical system was satisfactory, roof structure was damaged by a fire and repairs were made, it is unknown weather those repairs were done properly or not. Lots of repairs and foundational movement were present in crawlspace. Leaning perimeter piers were present, pilaster’s were damaged and or in the middle of repairs. Roof structure and foundation were going to need further evaluation by a licensed contractor and a list of repairs made for the potential buyer.

Improper repairs to foundation

Another happy client in the Charlotte market. Charlotte North Carolina week of 7/20/2020. Several items of note on this summary. Water management issues abound in crawlspace, efflorescence present water on floor present, watermarks present on foundation volunteers. Improper renovations (DIY) were done under the bathroom in crawlspace. Additionally, there appeared to be a wood destroying fungus growing on for Joyce Emma very damp wet area. Additionally, there appeared to be a wood destroying fungus growing on for Joyce Emma very damp wet area. All of these items and many others on some rework called out and required further evaluation by a licensed contractor.

Happy Charlotte Clients

Another happy client in the Charlotte North Carolina market. Highlighted in this inspection is a clear WDIR wood destroying insect report on crawlspace, but un-repaired and poorly repaired termite damage was present in this crawlspace. Deteriorated floor Joists, sill plate, sheathing were present. Additionally temporary supports were present as well. All defects were recommended for further evaluation by a licensed general contractor

Building a Culture of Preparedness

Building a Culture of Preparedness
JULY 7, 2020 REALTOR PARTY NEWS

Download Resources for Real Estate Professionals Today!
No one could have prepared for what 2020 has had in store for us to date. But there are situations that REALTORS® and homeowners should be prepared for — hurricane season.

Market activity is returning to full swing. That likely brings added questions from potential new customers looking at homes in flood-prone areas. That’s why NAR has worked with the Federal Emergency Management Agency (FEMA) on a suite of flood resources to help you advise your clients.

Use these resources, web pages, fact sheets, infographics, and publications to promote the financial protection flood insurance offers and explain various flood insurance requirements to homeowners and business owners.

Also be prepared to answer customers’ questions about a new, searchable website created to help people assess the flood risk of particular properties. The site shows that millions more homes potentially fall into flood zones than FEMA flood maps suggest. FEMA’s flood maps have served as the standard for lenders in determining flood insurance requirements for a mortgage under federal law. This new site developed by nonprofit research firm the First Street Foundation allows homeowners, real estate professionals, lenders, and others to find detailed flood risk information on specific properties nationwide.

Building a culture of preparedness requires that we raise awareness that a property does not need to be near water to food. In fact, more than 40% of all National Flood Insurance Program (NFIP) food claims come from outside high-risk areas. Floods can be a result of storms, melting snow, hurricanes, water backup, broken water mains, and changes to land as the result of new construction, among other things.

Electrical panel safety

While inspecting the outside of a house a couple years ago, Joe Mazza of Exclusive Home Inspection in New York encountered a metal grating, like a louver, that went into the crawlspace under the property. According to Mazza, the grating was installed incorrectly. It wasn’t screwed in, so it was just sort of hanging there. A wire and with a plug were protruding out the of grating. The plug appeared to be for a generator. Someone had wired it into a 30-amp breaker, but there was no interlocking kit. Both the breaker and the panel were on.

Wanting to move the metal grating aside, Mazza reached out and touched it. He slid the grating over with his palms against the concrete siding of the house

electrical exposures“[The grating] touched the plug. Sparks flew. Flames shot up. [The electricity] hit my arm [and] shot me back about five feet,” Mazza said. “[I] saw stars [and was] shaking like crazy.”

Mazza hadn’t realized that the wire was live. Had he known—or been more cautious—he would have tested the line before touching the metal grating.

“It was a huge wake-up call for me. If I [had been] grabbing that metal grating, I would have died. If my face [had been] against it, it would have burnt my face,” Mazza said. “That night, I came home, I laid in bed, [and] I didn’t sleep the entire night. I literally sat there, and I stared at my six-year-old-daughter, and [I] was just thankful that I was able to do that.”

Electrical exposures and home inspectors.
Inspecting homes is a dangerous job. From slippery roofs to aggressive animals, rotted subflooring to invisible toxins, the average home inspector encounters countless perils during their careers. One hazard that can be fatal is electrical exposures.

“[Electrical exposures] can take your life if you’re not prepared,” said Walter L. Williams of PPT Inspections in Michigan. “Even if you put an instrument to [a wire] to get a reading, or to see if it’s energized, you don’t know what may be lurking behind the [electrical] box.”

To Williams’ point, one reason electrical exposures pose such a risk is because of how difficult they are to identify.

“You can’t see electricity. You can’t smell it, [and] you can’t taste it. But you feel it, and it hurts really bad,” said Julian Cofer of Cofer Real Estate Inspections in Texas.

Injury types.

According to the Canadian Centre for Occupational Health and Safety (CCOHS), electrical currents cause four main types of injuries:

Electrocution
Electric shock
Burns
Falls
Each of these four injury types can happen to a home inspector. Here are some examples of scenarios in which you could encounter a hot or live wire and sustain an injury:

To get to the electrical panel, a home inspector leans across a washing machine. Conductive to electricity, the metal and improperly grounded machine transfers a shock to the inspector.
While in an attic, a home inspector brushes against a live wire hidden in the insulation.
The inspector steps through a puddle of water in the basement. As he continues to inspect, he encounters some energized wires that electrocute him.
While inspecting the electrical panel, an inspector touches an energized circuit part. The shock burns his hand and sends him flying backward several feet.
Thankfully, suffering from an electrical injury on the job is avoidable. There are ways for you to manage your risk against harm. In this article, we discuss some precautions and resources to overcome electrical exposures you may encounter on the job.

How can you avoid electrical injuries?
Know what you’re looking for.

Understanding the conditions of the wiring system can help you stay safe during your inspection. Start by taking a thorough electrical inspection course, like those offered by local or national associations or by training schools. (For example, consider taking Mike Twitty’s History of Electrical Codes and Wiring Methods course, available on the ASHI Online Learning Center (AOLC).)

electrical exposuresWhile it’s not always possible to know the history of the electrical system prior to your inspection, making a habit of asking beforehand gives sellers the opportunity to alert you of potential electrical hazards. Also, knowing the year the home was built can help you predict what electrical issues you may encounter. (For example, a house built in the 1930s may have knob-and-tube wiring while a new build will not. You can learn more about avoiding knob-and-tube and other common electrical claims here.)

In addition to understanding electrical inspection basics, it’s good to know the warning signs that may indicate that an electrical system is dangerous. The InterNACHI online education course “How to Perform Residential Electrical Inspections” lists several.

There are warning signs that a panel, box, or the system in general may be compromised, and these should persuade the inspector to defer further evaluation to a licensed electrical contractor:
scorch marks on the dead front or the panelboard door, indicating a past or recent arc flash;
rust, which indicates past or recent moisture intrusion;
missing or open breakers that cannot be confirmed to be de-energized;
overloading of the circuits with DIY wiring;
uninsulated wiring;
excessive dust, dirt and debris inside the panelboard; and/or
any signs of water inside, around or below the panelboard, which can lead to shock or electrocution.
Dress appropriately.

How you dress can provide you with literal layers of protection against electrical exposures. Many of the inspectors we interviewed wear insulated gloves, eye protection, and/or rubber-soled shoes to protect against electrical currents. Some of them know inspectors who even wear face shields and are considering starting to wear them themselves.

“If you look at the OSHA rules, when you’re messing with panels, you’re actually supposed to have a face shield on,” said Alan Grubb of 4U Home, Inc. in Maryland. “We haven’t required face shields ourselves yet, although I’m very well thinking about it. The more I read up on [electrical hazards], the more they scare me.”

While not discussed in the interviews, its’ worth mentioning that electricians avoid wearing jewelry—such as rings and watches—and carry insulated tools during the job. As indicated earlier, metal can exacerbate electrical hazards. Thus, avoiding wearing and carrying unnecessary metal materials is a great way to manage your risk.

Don’t become complacent.

When Mazza was shocked during his inspection, he had a voltage tester on him. He could have used it to verify that the wiring wasn’t energized. But he didn’t. According to Mazza, the routine nature of his home inspections had led him to be complacent, which put him in a dangerous situation.

Williams agrees that focusing on the task at hand is a big part of managing your risk.

“Most things happen when our mind is not set on the inspection,” Williams said. “If we’re not mentally checked-in on the inspection, we do short cuts, and bad things can happen.”

Bad things do happen, like Mazza’s shock or even an electrically induced fall. In his article “Understanding Non-Contact Voltage Testers,” Brad Deal of 20/20 Home Inspections in California describes how a non-fatal shock could prove deadly when an inspector isn’t aware of his environment.

“There is a natural tendency to suddenly withdraw from a shock. The quick withdrawal of a hand can cause you to impale yourself on nearby metal edges, or if you are on a ladder, then the momentum could cause you to pull the ladder over the center of balance and fall,” Deal wrote. “You always must be cognizant of your surroundings and the potential repercussions of a shock. Was it the shock or the fall that killed him?”

When you use them, make sure to use ladders and pole cameras made of non-conductive (not metal) materials, like wood, fiberglass, or carbon fiber. According to Jim Troth of Habitation Investigation in Ohio, even having an aluminum tip on your ladder or pole cam may result in an injury. Additionally, you can also set up such equipment away from electrical power lines and other sources of electrical exposure.

electrical exposuresWatch out for water.

Being aware of your surroundings doesn’t end with being cognizant of metal. Water, too, greatly increases the danger of an electrical inspection.

According to the U.S. Geological Survey (USGS), water’s ions and impurities make it a powerful conductor of electricity. That means that water anywhere near anything electrical can pose a significant hazard. As such, it’s important not to go near a panel with water around it.

“If there’s water dripping on the panel, don’t touch it. If there’s water on the floor underneath the panel, don’t touch the panel. Don’t even consider opening it up,” Troth said.

Additionally, water in attics and crawlspaces can pose a risk. Recently, former electrician Ryan Schmidt of Broadneck Home Inspections, LLC in Maryland encountered a crawlspace full of standing water about four inches deep.

“I just didn’t go into the crawlspace because you just don’t know if there’s a wire lying in the water somewhere,” Schmidt said. “I just make a notation, take pictures of it [to] show that that’s the current condition, and then I call it out in the report as being unsafe to enter.”

William Chandler of Property360, LLC in Florida, too, won’t enter a crawlspace with water in it due to the chance of encountering a hidden electrical exposure.

“We can’t always see if there’s electric wire. We find live wires buried in insulation and underneath a little bit of dirt,” Chandler said.

Always test.

Remember Mazza’s voltage tester? Because electrical exposure hazards aren’t always immediately apparent, you should test to ensure that the systems and components are safe before you inspect them.

Whether an electrical system is old or new, whether the seller says they’ve turned off the electrical or not, Tim Woodcock of First Choice Property Inspections, LLC in Florida cautions home inspectors not to make assumptions about wiring conditions. Rather, he suggests always treating the electrical system as if it’s energized.

“Even though you are told that [the wiring is] all dead and [the sellers] just haven’t removed it, you treat it as alive,” Woodcock said. “I’ve seen that knob-and-tube writing up in some of these older Florida homes, and I’ll put the [voltage] meter on it. That thing will light up—even though it was supposed to be disconnected.”

To verify whether something’s energized, most of the home inspectors we interviewed, including Mazza and Woodcock, recommend using a non-contact electrical tester—also referred to as a voltage proximity tester, voltage sniffer, glow-tip, and TIC tracer, among other names. While such testers are somewhat proficient in diagnosing electrical issues, the inspectors we interviewed recommended using testers primarily as a safety device.

Safety capabilities.

Here are some examples of what a non-contact tester can do to help keep you safe:

Check if wires are live
Identity energized circuits
Locate missing or discontinuous grounds
Find wires hidden behind walls, underground, or inside electrical boxes
Discover metallic fixtures underground
Identify blown fuses
Locate neutrals, ground faults, or high voltage lines
Check a circuit for completeness
Note that, in addition to having diagnostic limitations, non-contact voltage testers have safety limitations, too. Every tester is subject to false positive and false negative readings, which vary based on the tester you use. To determine your tester’s limitations, consult your tester’s user manual.

Don’t have a non-contact voltage tester yet? You can purchase one from a hardware store or an online retailer for around $30.

Consider using a thermal imaging camera.

Both Schmidt and Williams use thermal imaging cameras to identify electrical hot spots in the connections, circuit breaker, or fuses. Schmidt estimates that one in every 30 houses he inspects has an electrical overload issue.

If the camera does identify an issue, Williams suggests communicating the potential defect to the client.

“If there’s [an] unusual reading from the infrared camera, I just put a note in my inspection report that it should be inspected by an electrician,” Williams said.

Infrared cameras do have their limitations. In his article “Testing Electrical Systems” for the ASHI Reporter, Mike Twitty of Homescan Property Inspections in Tennessee explained that thermal readings are not conclusive and must be verified.

“A thermal camera can indicate a suspected overloaded circuit but only can be confirmed by following up with an amp reading on the loaded circuit,” Twitty wrote.

Interested in learning more about thermal imaging? Read our article “Infrared Cameras: Redefining the visual, non-invasive home inspection.”

electrical exposuresBe wary of the electrical panel.

Many of the techniques you can implement to manage your risk against electrical exposures apply to a wide variety of circumstances. However, electrical panel safety warrants a section all its own.

“One of the most dangerous parts of the inspection is opening up the electrical panel,” Schmidt said.

In his article “Electrical Service Panels,” InterNACHI founder Nick Gromicko suggests that home inspectors ask themselves four questions prior to touching an electrical panel:

Do I have an escape path? Make sure that you know where you can safely turn or step if you must safely escape a dangerous surprise, such as bees or sparks. An unfortunately placed shovel or extension cord, for instance, can turn a quick jerk into a dangerous fall.
Are the floors wet? Never touch any electrical equipment while standing on a wet surface!
Does the panel appear to be wet? Check overhead for dripping water that has condensed on a cold-water pipe. Moisture can arrive in more ways than you can imagine.
Is the panel rusty? Rust is an indication of previous wet conditions that may still exist.
Once the panel is open, you should refrain from touching the components of the panel—even to move conductors aside or to read labels. Touching energized electrical components can lead to electrical injuries. Rather than reaching into the panel, InterNACHI suggests explaining that you were unable to safely retrieve whatever information you’re lacking in your inspection report.

Panel Screw Hazards.

In its course “Safe Practices for the Home Inspector,” InterNACHI adds a caution against opening a panel that’s original screws have been replaced with improper substitutes.

“The risk of cutting through the insulation that protects the wire conductors may be greater with the threads along the shaft of the screw than with the point of the screw,” the course explains. “InterNACHI recommends that inspectors not attempt to remove improper screws but, instead, disclaim conditions inside any affected panels and recommend correction by a qualified electrical contractor.”

Even if the screws themselves are correct, inspectors still face risks removing and replacing them. Michael Spaargaren of First Choice Inspectors in Illinois recommends against using electric screwdrivers—particularly when replacing the cover panel. According to Spaargaren, you might screw through insulation, short a circuit, and blow the breaker.

Client Concerns

Home inspectors aren’t the only ones at risk whiling inspecting the electrical panel. The electrical exposure here is a shock hazard for clients and homeowners, too.

“Sometimes, you’re taking panel covers off, and panels might be below the recommended height. And if they’ve got a small or inquisitive child, they could easily stick their hand in there,” Spaargaren said.

To circumvent potential dangers to clients and other observers, Schmidt added a section to his pre-inspection agreement. As part of Schmidt’s contract, clients agree to give him space while he’s inspecting the electrical panel. See the excerpt below:

Electrical Panel: Clients must stay back 10’ away from the electrical panel while inspector has the cover removed and is conducting the panel inspection.

Alternatively, Williams recommends creating some signage that cautions laypeople against approaching potentially dangerous systems or components—like the electrical panel—during the inspection.

If it’s too dangerous, skip it.

Whether you’re inspecting the electrical or any other system, it’s important to always put your safety first.

“If you’re unsure about something, don’t touch it. Get a professional. Even though most of us are licensed professional inspectors, we’re just generalists. If you’re unsure about something, just get the resident expert out there to take a look at it,” Cofer said.

Chandler reminds inspectors that it isn’t their job to find every issue with a property. Furthermore, choosing to report an area or component as inaccessible due to a safety concern is perfectly reasonable.

“The inspector has to be aware of what could hurt them and do a reasonable assessment,” Chandler said. “’Is this something I should be doing? Am I willing to risk my life for $400?’”

What resources are available to home inspectors who are injured by electrical exposures?
If you or one of your home inspectors is injured by an electrical exposure on the job, workers’ compensation benefits may be available to you.

Workers’ comp insurance provides employees who suffer from work-related injuries or diseases with access to medical and wage benefits. Unlike general liability (GL) insurance, which covers inspection-related bodily injury and property damage claims for non-employees, workers’ compensation looks out for you and the people who work for your company.

“One accident can not only hurt you and maybe put you out of business, but more importantly, that employee has to have a way of making a living getting his bills paid for it if it happens on the job,” Grubb said.

By covering job-related injury and illness costs, workers’ comp protects both employees and employers. Employees work under less financial risk knowing they have on-the-job protection. Additionally, employers limit their liability and deter litigation.

“If you have any employees, they need to have workman’s comp,” Grubb said. “The amount that it costs for workman’s comp is minor [compared] to what it could cost you or your employee if you didn’t have it.”

What expenses can workers’ comp cover?

In electrical exposure injury cases, workers’ comp coverage can assist inspectors in the following ways:

Medical Bills. From doctor appointments to hospital visits, to medications and mobility aids, workers’ comp helps pay to treat employee illnesses and injuries. Workers’ comp can even help inspectors pay for their mileage when traveling to receive medical care.
Lost Wages. Sometimes, electrical-related injuries and illnesses are bad enough that employees are unable to work. Workers’ comp can pay a percentage of the money the employee would be earning if they weren’t in recovery.
Rehabilitation. Workers’ comp policies may offer medical rehab benefits, like physical therapy, to help employees recover. They can also help pay for vocational rehab for severely injured employees unable to perform their previous jobs. By helping these injured employees attain new abilities, vocational rehab helps them return to work in a different role.
Death. If an employee died, the employer’s workers’ comp insurance may help cover funeral costs and lost income.
Note that, since states regulate workers’ comp coverage, the amounts insurers will pay for the above benefits varies from state to state.

“Each state has its own regulations as to the amount and duration of lost income benefits and medical or rehabilitation services,” said Brianne Meagan, InspectorPro broker and workers’ comp specialist. “However, workers’ comp is a no-fault coverage nationwide. That means it will provide coverage no matter who was at fault.”

Protect your business and your employees with workers’ comp insurance.

Do your part to abide by state law and protect your employees and your business by carrying workers’ compensation insurance. And do so with a company prepared to meet the inspection industry’s unique coverage needs.

“Things happen when you go out and inspect. And if something goes wrong, you want to make sure that you are covered…. I don’t want to be the one who doesn’t have the proper insurance in case something goes wrong,” Williams said. “For a few dollars more, [workers’ comp] is going to give you peace of mind.”

Inspection Charlotte North Carolina

Another satisfied customer on a Charlotte North Carolina inspection. A somewhat extensive summary on this home with a couple items of note. 1. there is an active leak underneath the kitchen with 100% moisture readings and visibly wet wood. The source of the leak was unknown. There was also some wood rot underneath bay window rear side of home. Mostly water management issues were present in crawlspace and exterior. Home was built on a hill that sloped left right leaving a low spot on the left side of crawlspace. Sump pump in this area was operational but appeared to be undersized for the amount of water that collects here. Watermarks, water on floor, water staining to foundation wall and piers, and efflorescence were widespread in the crawlspace. All these items were highlighted in the summary, and a licensed contractor will need to be called out for further evaluation and or correction of these defects.

Polybutylene Supply Lines

Another happy and satisfied Rock Hill client. This was a pre-sale inspection. Although the summary page was quite extensive, with multiple minor issues, 3 main issues were present and of note. 1. Hardboard siding on the exterior showing extensive rot. 2. Water management issues around exterior perimeter of home. 3. Polybutylene plumbing lines present throughout crawlspace and interior. Polybutylene plumbing was installed from approximately 1975 through 1994 and it appears as a grayish supply line with copper fittings. There was a recall on this material, class action lawsuits were litigated. The problem is apparently that the chlorine in city water would react with the copper and plastic materials causing sudden failure, thus the recall. The recommendation it’s to replace all polybutylene plumbing by licensed contractor.

Another client Happy as a clam!

IMG_1357

Today 7/9/2020. Another client “happy as a clam!” Inspected a house in the greater Charlotte area today. A three bedroom two bath. The home had considerably lengthy summary which included an active termite infestation sill, joist, and ledger Board damage. The highlighted defect is a defective three-way switch for the ceiling fan in living room. A potential short in the wiring is preventing it from turning off the light. Among other concerns on the summary this electrical concern was highlighted as a defect, and the recommendation is for a licensed electrical contractor to you come out and repair.

Dave Tursi
inspectiondetective.com
PPR Home Inspections Inc.
704 737 4648